No worries! Check out CoralVue's new Outlet and Parts Store for a variety of aquarium supply parts, open-box items, repair services, and more
JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser.
In this exciting episode, we will cover the assembly and installation of the brand new Klir filter by CoralVue!
By far, one of the biggest husbandry complaints from reefers today is a filter sock. While the benefits of filter socks are undeniable, so are the frustrations. Filter socks help us keep our tanks clean by filtering water and trapping debris making it easy for us to remove.
The problem is that they still require us to remember to remove them. If we do not or forget to do so, the filter sock will clog up to the point that water will not get pass through them.
While this is not such a bad thing, the trapped food and debris within the sock will soon begin to decay and release unwanted nutrients back into the water.
Not only that, after removing filter socks, they are smelly and something we rather not deal with. Who hasn’t gotten the look from their signification other when you try to wash the filter socks on the same laundry machine that washes your families clothes.
Solution, fleece filter machine… or is it a solution really? The fleece filter is a great concept… a machine that has a roll of fine clothe material. Water is ran through the material and filtered. As the material gets used and clogged up, the machine replaces it with new clean cloth. Once the roll is used up, the hobbyists tosses the dirty roll and replaces it with a new one. This sounds great but… yes, there is a but!!!
The current machines are expensive, they all require additional space within or above the sump and they all require intricate plumbing modifications, making it a hassle to install into existing setups.
The Klir filter by CoralVue is a machine that takes the best of both worlds to create a one-of-a-kind patent pending cleaning machine. Water passes through the Klir filter and as the filtering material becomes saturated with waste, the water level will begin to rise.
When the water makes contact with the optical sensor, a motor is activated to advance new clean filtering material.
As clean material is exposed, water is now able to flow freely, lowering the water level in the sock tray and deactivating the motor.
This process is repeated as needed, allowing you to forget about filter maintenance!
Unlike other filters on the market, the Klir does not take any additional space inside, above, behind or next to the sump. Simply remove your filter sock from it’s holder and drop the Klir filter in it’s place. The klir is a true plug-and-play filter!
Before we proceed with the installation, let’s make sure that our system is fully compatible with the Klir filter.
The sump should have:
In addition to sump compatibility, we also need to make sure that the Klir can handle the flow speed going into our sumps.
The number of Klir units needed is not based on the number of filter socks your sump holds. Just because your sump can hold 2 filter socks does not mean that you require two Klir filters.
The number of units needed is mainly based on total water flow going into the sump.
So if you have a sump that holds two filter socks but you are only moving 600gph, you technically only need one Klir filter. You can then install a diverter cap, which is sold separately, on the open filter sock holder to either close or reduce the flow that will bypass the Klir filter.
On the other hand, if you have the same sump and you are moving 1000 gph, you will need to run two Klir fiters in a master/slave setting where both Klir filter motors are connected to a single controller with a single sensor.
Now that we’ve covered the system requirements, let’s begin the Assembly & Installation of the Klir Filter.
Before we proceed with the assembly, let’s make sure that all components are included and nothing is missing from the box.
The Klir should include:
To begin assembly, open the filter and insert the short-side of the rubber vent pipe into the holder leaving the long side upwards.
Insert the optical sensor into the slot on the main body and tighten the nut.
Assembly is now complete. Now it is time to thread the fleece in place.
Remove the cover from the unit as well as the sidewall from the bottom chamber.
Take the supply spindle, which is the larger of the two, and inserting it into the roll.
Load into the cradle making sure that it rolls over and not under.
Pull the fleece over the first guide roller and then under the second roller on the base of the unit.