IceCap EVO 3000 Water Pump
SKU: IC-EVO-3000
MSRP: $ 93,37
-
Available Through Authorized Retailer
- The IceCap EVO 3000 also comes in a larger size, delivering up to 790 GPH for freshwater and marine tanks.
- It is built for hobbyists needing a return pump, reactor feed, or algae scrubber pump for larger setups.
- It runs on 49 watts and reaches 7.5ft of head, suited to taller or higher-flow plumbing runs.
- Its larger 6.5 x 4 x 5.25in body and 3/4–1in outlet handle more volume than the EVO 1000 or 2000.
IceCap
Premium aquarium equipment without the premium price. Protein skimmers, pumps, reactors, heaters & more.
A Larger Water Pump for High-Flow Applications
The IceCap EVO 3000 steps up further from the EVO 1000 and 2000, built for larger aquariums or applications that need more flow and head height. It can be used as a return pump, to provide flow to a media reactor, to feed an algae scrubber, or for other general water-moving tasks in the system.
Delivering up to 790 GPH with 7.5ft of maximum head height, the EVO 3000 suits larger aquariums or setups with a longer or taller plumbing run than the smaller EVO models can handle.
Key Features:
- Delivers up to 790 GPH of flow
- Maximum head height of 7.5 ft
- Runs on 49 watts
- Larger 6.5 x 4 x 5.25in body suited to higher-volume applications
- 3/4–1in hose barb outlet accommodates larger plumbing
- Suitable for both freshwater and marine aquariums
Ideal For:
- Larger aquarium return pump applications
- Systems with a longer or taller plumbing run
- Feeding a media reactor or algae scrubber that needs high flow
Pro Tips:
- Match head height to your plumbing run. With a 7.5ft maximum head, the EVO 3000 handles taller vertical lifts better than the smaller EVO models.
- Check your outlet size before plumbing in. The larger 3/4–1in hose barb outlet may require different tubing than the EVO 1000 or 2000.
What’s Included:
(1) IceCap EVO 3000 AC Water Pump Unit
(1) Mounting Base Plate with Rubber Suction Feet (IP-EVO3000-BS)
(1) Stepped 3/4 in to 1 in Hose Barb Outlet Fitting
Technical Specs:
SKU / Factory Part Identifier: IC-EVO-3000
Maximum Flow Rate: 790 GPH
Maximum Head Height: 7.5 Feet
Power Consumption: 49 Watts
Operating Voltage: 110V AC / 60Hz
Dimensions (L x W x H): 6.5 in x 4.0 in x 5.25 in
Outlet Connection: 3/4 in to 1 in Hose Barb
Primary Compatibility: Freshwater & Saltwater Aquariums, Sumps, and Reactors
Warranty
CoralVue, Inc. hereby guarantees this product to be free from defects in material and workmanship for a period of:
- 1 Year
Warranty is activated on the date of purchase.
This Standard Limited Warranty applies and is limited as follows:
- To the product only as long as it remains in the possession of the original purchaser.
- To the product that has not been subject to accident, misuse or abuse.
- To the product that has not been modified, altered, defaced, or had repairs made or attempted by other than CoralVue, Inc.
- That CoralVue be immediately notified in writing within ten (10) days of first knowledge of defect by owner or his agent.
- That CoralVue, Inc. shall be given first opportunity to make any repairs, replacements or corrections to the defective construction within a reasonable period of time.
- Under no circumstances shall CoralVue and/or the Manufacturer be liable by virtue of this warranty or otherwise for damage to any person or property whatsoever for any special, indirect, secondary or consequential damages of any nature however arising out of the use or inability to use because of the product defect.
Installation & Set-Up Guidelines:
Attach the base plate with suction feet onto the bottom tracks of the EVO 3000 pump motor block.
Thread the stepped 3/4" – 1" hose barb fitting onto the pump discharge port.
Submerge the pump completely into your sump, rear filtration chamber, or water reservoir.
Push flexible vinyl tubing onto the hose barb fitting and secure it with a plastic ratchet hose clamp.
Plug the 110V AC power cord into an electrical outlet or power strip, creating a safety drip loop in the cord.
Pro Tips:
- Create a Power Cord Drip Loop. Because the EVO 3000 plugs directly into a standard 110V AC outlet, always ensure the power cord droops lower than the wall outlet. This prevents stray water droplets from traveling down the cord into the electrical socket.
- Soak in Vinegar During Routine Maintenance. Every 3 to 6 months, unplug the pump, remove the front cover and magnetic rotor, and soak them in warm white vinegar or citric acid solution. Clearing calcium and detritus prevents rotor drag and ensures quiet operation.