Reeflo SwordTail
$299.00

Reeflo Swordtail Pressure Rated 1750gph Water Pump

  • SKU: RLO-SWTL

Max Flow: 1750gph | Max Head: 20ft

Power Consumption: 150w average
Dimensions(L x W x H):11" x 6.57" x 7" {2" inlet /1½" outlet}

New pressure rated version of the Reeflo Dart that is perfect for 75-150 gallon tanks. Uses the same motor and pump head but the impeller is customized to allow to flow up to 20' of head pressure.

$299.00
Features
Overview

Pressure Rated Reeflo SwordTail

The SwordTail is our new pressure rated version of the Dart that is perfect for 75-150 gallon tanks. It uses the same motor and pump head but the impeller is customized to allow to flow up to 20' of head pressure.

Watt Draw=155 watts
3 year warranty

Ports are 2" FNPT suction and 1-1/2" FNPT discharge. But don't worry, if you want or need to use smaller plumbing, go ahead and reduce it down! All you need to do is add the desired bushing on the suction side, and then make sure the discharge/output is a smaller diameter than the suction.

For example, if you need to have a 1" output, then you just need to make sure the suction is 1" as well. Or if you know you want a 1" suction, then just make sure the output is the same 1" or less. Units are pre-wired with an 8' cord and molded 110V plug.

When it comes to external pumps,ReeFlo is truly in a class of its own.

Reeflo SwordTail Pump Specifications
Wattage: 155w average
Max Flow : 1750 gph
Max Head: 20ft
Dimensions (L x W x H):11" x 6.57" x 7"
Inlet Size: 2" FNPT
Outlet Size: 1½" FNPT

Measurements are approximate and can vary.

MORE DETAILS

- Suitable for both indoor and outdoor use. This is an external pump and can not be submersed in water! Do not allow this pump to get wet or run dry.

- Pump can be valved back as long as it is done on the DISCHARGE line. It will reduce the flow of the pump as well as the wattage.

Pump Type: Straight Centrifugal
Motor: Baldor, 12ft 3 pronged grounded cord.

FAQS

Tips & Troubleshooting
We hope you will find the following suggestions and comments regarding pump installation to be helpful. We do not claim that any of these suggestions are the only way to accomplish your job, but in general they will solve many of the commonly found problems and help you prevent many
others.Please note that ReeFlo pumps are external pumps. Do not submerge!

  1. Locate the pump as close to the source as possible. It is best to have your main (longest)run of pipe on the discharge side of the pump. The pump is designed to push water, not pull it.
  2. Always have your inlet pipe diameter equal to, or larger than, the discharge line. This helpsprevent cavitation.
  3. Never run a pump dry. This may damage the mechanical seal and impeller. They aredesigned to pump fluid, not air. Insure the pump is full of water before you turn it on, and thatit doesn’t out pump the supply.
  4. If your pump is producing too much flow, you can reduce the flow by partially closing avalve on the discharge line. Never restrict the inlet!!! Surprisingly, this will make the motor workless and use less electricity!! This “valving back" simply causes the pump to operate further backon its performance curve.
  5. If your pump is not producing enough flow. The easiest step is to widen the line especially onthe intake. As illustrated on the chart the narrowness of the line has great bearing on “frictionloss"....think bar straw vs. regular straw.
  6. If more flow is required than a single pump can produce, consider using two or morepumps in parallel. This will double the flow. If more pressure is required consider using twopumps in series (one feeding into the other). This will have the effect of doubling the pressure.We have found that using two pumps instead of one larger pump uses an average of 30% lesselectricity.
  7. Choose a pump that can give you the required flows at the lowest possible powerconsumption. Since pumps often operate continuously, the power consumption (watts - notamps), and its effect on your monthly utility bill can be very significant.
  8. Check to be sure the motor electrical connections are set up to match the supply voltage.
  9. Install shut off valves before and after the pump, so you can easily remove it from the linewithout having to drain your system. Be sure to use ball valves, as they have low frictionloss characteristics.
  10. Use Teflon paste (not tape) for sealing threaded joints.
  11. Make sure all your pipe joints are airtight. This is especially important on the suction side.
Reviews

Customer Reviews

Review "Reeflo Swordtail Pressure Rated 1750gph Water Pump"

Write Your Own Review

Only registered users can write reviews. Please, log in or register

VIDEOS
DOWNLOADS